بررسی مقاومت فشاری و خمشی بتن‌های پلیمری حاوی الیاف پلی وینیل الکل و پلی پروپیلن بر پایه‌ی رزین اپوکسی

[1] K. P. Mehta, "Reducing the environmental impact of concrete," Concrete international, vol. 23, pp. 61-66, 2001.

[2] D. W. F. Milton Anderson, "ACI 548 Polymer-Modified Concrete," ACI Committee 548, p. 48, 1997.

[3] M. Nodehi. "Epoxy, polyester and vinyl ester based polymer concrete: a review". Innov. Infrastruct. Solut. 7, 64, 2022.

[4] Bedi, R., Chandra, R., & Singh, S. P. "Mechanical properties of polymer concrete". Journal of Composites, 1-12 ,2013.

[5] Ataabadi, H. S., Zare, A., Rahmani, H., Sedaghatdoost, A., & Mirzaei, E. "Lightweight dense polymer concrete exposed to chemical condition and various temperatures: An experimental investigation". Journal of Building Engineering, 34, 101878, 2021.

[6] J. Reis, "Mechanical characterization of polymer mortars exposed to degradation solutions," Construction and Building Materials, vol. 23, pp. 3328-3331, 2009.

[7] V. Toufigh, M. Hosseinali, and S. M. Shirkhorshidi, "Experimental study and constitutive modeling of polymer concrete’s behavior in compression," Construction and Building Materials, vol. 112, pp. 183-190, 2016.

[8] Verma, A., Baurai, K., Sanjay, M. R., & Siengchin, S. "Mechanical, microstructural, and thermal characterization insights of pyrolyzed carbon black from waste tires reinforced epoxy nanocomposites for coating application". Polymer Composites, 41(1), 338-349, 2020.

[9] Verma, Akarsh, and V. K. Singh. "Mechanical, microstructural and thermal characterization of epoxy-based human hair–reinforced composites." Journal of Testing and Evaluation 47.2 ,1193-1215, 2018.

[10] Akın, M. H., & Polat, R." The effect of vehicle waste tires on the mechanical, hardness and stress–strain properties of polyester-based polymer concretes". Construction and Building Materials, 325, 126741, 2022.

[11] P. Nóvoa, M. Ribeiro, A. Ferreira, and A. Marques, "Mechanical characterization of lightweight polymer mortar modified with cork granulates," Composites science and technology, vol. 64, pp. 2197-2205, 2004.

[12] K. Jafari and V. Toufigh, "Experimental and analytical evaluation of rubberized polymer concrete," Construction and Building Materials, vol. 155, pp. 495-510, 2017.

[13] Martínez-Barrera, Gonzalo, Osman Gencel, and Miguel Martínez-López. "Performance improvement of polymer concrete produced with unsaturated resin, by a post-cure process, polyester fibers and gamma radiation." Journal of Building Engineering 59: 105117, 2022.

[14] Karamzadeh, Nima Shahni, M. R. M. Aliha, and Hamid Reza Karimi. "Investigation of the effect of components on tensile strength and mode-I fracture toughness of polymer concrete." Arabian Journal of Geosciences 15.13: 1213, 2022.

[15] Farooq, Mohammed, and Nemkumar Banthia. "Strain-hardening fiber reinforced polymer concrete with a low carbon footprint." Construction and Building Materials 314: 125705, 2022.

[16] J. M. L. d. Reis, "Mechanical characterization of fiber reinforced polymer concrete," Materials Research, vol. 8, pp. 357-360, 2005.

[17] O. Elalaoui, E. Ghorbel, V. Mignot, and M. B. Ouezdou, "Mechanical and physical properties of epoxy polymer concrete after exposure to temperatures up to 250 C," Construction and Building Materials, vol. 27, pp. 415-424, 2012.

[18] O. Elalaoui, E. Ghorbel, and M. B. Ouezdou, "Influence of flame retardant addition on the durability of epoxy based polymer concrete after exposition to elevated temperature," Construction and Building Materials, vol. 192, pp. 233-239, 2018.

[22] A. C136, "Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates," ASTM International, 2014.

[23] K. Jafari, M. Tabatabaeian, A. Joshaghani, and T. Ozbakkaloglu, "Optimizing the mixture design of polymer concrete: An experimental investigation," Construction and Building Materials, vol. 167, pp. 185, 2018.

[24] ASTM C579, "Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes," Annual book of ASTM standards. Pennsylvania, 2010.

[25] ASTM, C469/C469M-14: Standard test method for static Q10 modulus of elasticity and Poisson's ratio of concrete in compression in Annual Book of ASTM Standards 2014.

[26] ASTM C580, "Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, andPolymer Concretes," Annual book of ASTM standards. Pennsylvania, 2010.